Incubator BF series

• Electronically controlled APT.line™ preheating chamber assuring temperature accuracy and reproducible results
• Temperature range 5 °C (41 °F) above ambient up to 100 °C (212 °F)
• Digital temperature setting with an accuracy of a tenth of a degree
• MS controller with several timer functions
• Time functions:
• 0 to 99 h 59 min delayed ON
• 0 to 99 h 59 min delayed OFF
• 0 to 99 h 59 min temperature-dependent
• delayed OFF
• Adjustable fan speed
• Adjustable ventilation by means of rear exhaust duct, Ø 50 mm (1.97 inch) with ventilation flap and front ventilation slide
• Inner glass door
• Independent adjustable temperature safety device class 3.1, providing full protection against chamber over-temperature, with visual alarm
• RS 422 interface for use with optional GMP/GLP and FDA guideline 21 CFR Part 11 compliant APT-COM™ DataControlSystem software, or switch over to printer output with RS 232 / RS 422 interface converter
• Adjustable intervals for printer
• Units up to 115 liters are stackable
• 2 chrome-plated racks included
• BINDER test certificate

		BF 720
	Exterior dimensions
	Width (mm/inch)	1234 / 48.6
	Height (inclusive castors) (mm/inch)	1528 / 60.2
	Depth (mm/inch)	865 / 34.1
	Plus door handle and exhaust duct (mm/inch)	90 / 3.5
	Wall clearance rear (mm/inch)	100 / 3.9
	Wall clearance side (mm/inch)	160 / 6.3
	Exhaust duct outer- Ø (mm/inch)	52 / 2.1
	Steam space volume (l/cu.ft.)	808 / 28.6
	Number of doors	2
	Interior dimensions
	Width (mm/inch)	1000 / 39.4
	Height (mm/inch)	1200 / 47.2
	Depth (mm/inch)	600 / 23.6
	Interior volume (l/cu.ft.)	720 / 25.7
	Racks, chrome-plated (number standard/max.)	2 / 15
	Load per rack (kg/lbs.)	45 / 99
	Permitted total load (kg/lbs.)	120 / 265
	Weight of the unit (empty) (kg/lbs.)	180 / 397
	Temperature data
	Temperature range, 5 °C (41 °F) above ambient up to (°C / °F)	100 / 212
	Temperature variation 1)
	at 37 °C (± °C)	0.4
	at 50 °C (± °C)	0.6
	Temperature fluctuation
	at 37 °C (± °C)	0.1
	at 50 °C (± °C)	0.2
	Heating up time 2)
	to 37 °C (Min.) 98 %	21
	to 50 °C (Min.) 98 %	24
	Recov. time after door was opened for 30 sec. 2)
	at 37 °C (Min.)	1
	at 50 °C (Min.)	4
	Air change at 70 °C (x/h)	11
	Electrical data
	Housing protection acc. to EN 60529	IP 20
	Nominal voltage (±10 %) 50 / 60 Hz (V)	230
	Nominal voltage (±10 %) 60 Hz (V)	115
	Nominal power (kW)	1.25
	Energy consumption at 37 °C (W)	80

1) value without window
2) up to 98 % of the set value

All technical data are specified for units with standard equipment at an ambient temperature of  25 °C and a voltage fluctuation of ±10 %. The temperature data are determinated in accordance to factory standard following DIN 12880 respecting the recommended wall clearances of 10 % of the height, width and depth of the inner chamber. All indications are average values, typical for units produced in series. We reserve the right to alter technical specifications at all times.

• 

  Waterproof interior power socket in the inner chamber

  Connected to the main switch. To connect ancillary equipment inside the chamber.

• 

  Additional PT 100 temperature sensor

  In situ or flexible installation for exact temperature measurement within the specimen material; connects to a special plug on the back wall of the inner chamber.

• 

  BINDER Data Logger kits

  The new BINDER Data Logger kits for temperature can record temperature data of BINDER equipment. This finely tuned product solution also contains useful accessories for mounting the Logger on the BINDER unit, including cable bushings and a sensor mounting bracket.

• 

  Door lock

  Prevents unauthorized access and interference with processes in the chamber.

• 

  Access ports

  With silicon plugs for inserting external measuring devices into the chamber. Access ports with 10, 30, 50 mm (0.4, 1.2, 2 inch) diameter.