Incubator KB series

• Electronically controlled APT.line™ preheating chamber and patented DCT™ refrigeration system assuring temperature accuracy and reproducible results in both heating and cooling situations
• Temperature range -5 °C to 100 °C (23 °F to 212 °F)
• MP controller with 2 programs with 10 sections each, alternatively switchable to 1 program with 20 sections
• Integrated week program timer with real time function
• Adjustable ramp function via program editor
• Digital temperature setting with an accuracy of a tenth of a degree
• Adjustable fan speed
• Elapsed time indicator
• Independent adjustable temperature safety device class 3.1, providing full protection against chamber over-temperature, with visual and audible temperature alarm
• Inner glass doors
• RS 422 interface for communication software APT-COM™ DataControlSystem, or switch over to printer output with RS 232 / RS 422 interface converter
• Adjustable intervals for printer
• Access port with silicone plug Ø 30 mm (1.18 inch), left side
• 2 stainless steel racks
• BINDER test certificate

		KB 720 (E5.1)
	Exterior dimensions
	Width (mm/inch)	1250 / 49.2
	Height (inclusive castors) (mm/inch)	1925 / 75.8
	Depth (mm/inch)	887 / 34.9
	Plus door handle, I-panel, connection (mm/inch)	939 / 37
	Wall clearance (mm/inch)	100 / 3.9
	Wall clearance side (mm/inch)	100 / 3.9
	Steam space volume (l/cu.ft.)	918 / 32.4
	Number of doors	2
	Number of inner glass doors	2
	Interior dimensions
	Width (mm/inch)	970 / 38.2
	Height (mm/inch)	1250 / 49.2
	Depth (mm/inch)	576 / 22.7
	Interior volume (l/cu.ft.)	698 / 24.7
	Racks (number standard/max.)	2 / 15
	Load per rack (kg/lbs.)	45 / 99
	Permitted total load (kg/lbs.)	150 / 331
	Weight (empty) (kg/lbs.)	309 / 682
	Temperature data
	Temperature range (°C/°F) 1)	-5 - 100 / 23 - 212
	Temperature variation max. (± K)	0.5
	at 4 °C (39.2 °F) (± °C)	0.2
	at 25 °C (77 °F) (± °C)	0.2
	at 37 °C (98.6 °F) (± °C)	0.2
	Temperature fluctuation max. (± K)	0.1
	Max. heat compensation up to 40 °C (104 °F) (W)	600
	Recovery time after door was open for 30 sec 2)
	at 4 °C (39.2 °F) (Min.)	12
	at 25 °C (77 °F) (Min.)	1
	at 37 °C (98.6 °F) (Min.)	2
	Electrical data
	Housing protection acc. to EN 60529	IP 20
	Nominal voltage (±10 %) 50/60 Hz (V)	200 - 240
	Nominal voltage (±10 %) 60 Hz (V)	200 - 240
	Nominal power (kW)	2.3
	Energy consumption 3)
	at 4 °C (39.2 °F) (W)	435
	at 25 °C (77 °F) (W)	420
	at 37 °C (98.6 °F) (W)	510
	Noise level (dB (A))	53

1) Lower values are valid up to an ambient temperature of max. 25 °C ( 77 °F).
2) up to 98 % of the set value
3) these  values can be used upon calculation of air conditioning systems

All technical data is specified for units with standard equipment at an ambient temperature of 25 °C (77 °F) and a mains voltage fluctuation of ±10 %. The temperature data is determined in accordance to factory standard following DIN 12880, observing the recommended wall clearances of 10 % of the height, width, and depth of the inner chamber. Technical data refers to 100 % fan speed. All indications are average values, typical for units produced in series. We reserve the right to alter technical specifications at all times.

• 

  Waterproof interior socket

  Switchable waterproof interior socket 230 V AC (max. 500 W), IP 65 protected, with corresponding plug (IP 66 protected).

• 

  Additional PT 100 temperature sensor

  In situ or flexible installation for exact temperature measurement within the specimen material; connects to a special plug on the back wall of the inner chamber.

• 

  BINDER Data Logger kits

  The new BINDER Data Logger kits for temperature can record temperature data of BINDER equipment. This finely tuned product solution also contains useful accessories for mounting the Logger on the BINDER unit, including cable bushings and a sensor mounting bracket.

• 

  Calibration certificates and validation

  BINDER can significantly reduce the time and effort needed for equipment qualification and validation. We draw on unparalleled knowledge of our equipment applications and years of experience in certification.

• 

  Operational data documentation: APT-COM™ DataControlSystem

  The only standard software that guarantees seamless documentation of all testing parameters in compliance with standards. Can be fully validated in accordance with GLP/GMP and FDA 21 CFR Part 11.